RUBBER MAT GLUE
E6100
Quantity
301,6 ml
Surface
Covers 20-25 linear foot
Weight
2 lbs (0,9 kg)
Quantity per box
12 tubes
Characteristics:
- Very efficient and durable
- Easy and quick to use
- Serves as a finish at the joints
- Same color as our rubber mats
Description:
E6100® is a unique non-sag, non-flammable industrial adhesive formulated to meet high-performance requirements. It permanently bonds to more surfaces than virtually any other adhesive, providing exceptional adhesion to:
✅ Wood
✅ Metal
✅ Glass
✅ Fiberglass
✅ Ceramics
✅ Masonry
✅ Concrete
✅ Asphalt
✅ Leather
✅ Rubber
✅ PVC
✅ Neoprene
✅ Vinyl
✅ Many plastics
Thanks to its non-sag formula, the adhesive will not drip or run, making it ideal for vertical applications. It maintains a flexible bond even in extreme cold temperatures, will not crack or become brittle, and is excellent for bonding items exposed to vibrations.
🛑 Note: For applications exposed to direct sunlight, paint over the adhesive after curing to ensure UV resistance.
APPLICATIONS
- Vertical repairs on brick & mortar
- HVAC system repair
- Locking fasteners against vibrations
- Roof flashing & shingles repair
- Auto upholstery, paneling & molding
- And much more!
FEATURES & BENEFITS
✔ EASY TO USE – 10.2 fl oz cartridge fits standard caulking guns
✔ FLEXIBLE – Will not become brittle in cold weather, ideal for vibration-prone applications
✔ CHEMICAL RESISTANT – Safe for exposure to dilute acids & bases
✔ ABRASION RESISTANT – Great for bonding objects subject to wear
✔ WATERPROOF – Can be submerged in fresh and salt water after curing
✔ PAINTABLE – Paint to match surroundings or to provide UV resistance
TECHNICAL INFORMATION
PROPERTIES – UNCURED MATERIAL
- Color: Clear
- VOC Content: 2.0 g/l
- Solvent: Perchloroethylene
- Flammability: Non-flammable (in uncured liquid state)
- Density: 11.0 ± 0.1 lbs/gal
- Solids Content: 30% by weight / 40% by volume
- Viscosity: Non-sag; 100,000 cps
- Tack Time: ~4 minutes
- Set Time: 20 minutes*
- Full Cure Time:
- Thin film: 24 hours
- Thick film: 48-72 hours
- Storage: May thicken in cold temperatures; warm to room temperature before use
- Application Temperature: Ideal between 50°F – 90°F (10°C – 32°C)
- Freeze/Thaw Stability: Stable; allow to return to room temperature before use
- Shelf Life: 2 years (unopened)
*Depending on material, humidity, and temperature.
PROPERTIES – CURED MATERIAL
- Chemical Resistance: Excellent to water, dilute acids, and dilute bases
- Hardness: 80 Shore A
- Dielectric Strength: 400V/mil (ASTM D-149)
- Tensile Strength: 3800 lb/in² (ASTM D-412)
- Elongation: 900% (ASTM D-412)
- Temperature Range: -40°F to 180°F (-40°C to 82°C) (intermittent)
- UV Resistance: Paint over or use E6800
- Paint-Over Time: 24 hours
ADHESION TEST – 180° PEEL STRENGTH TEST (ASTM D903)
Average maximum peel strength in PLI (pounds per linear inch):
| Material | Adhesion (PLI) |
|---|---|
| Aluminum | 35 pli |
| Birch (Wood) | 40 pli |
| Glass | 34 pli |
| PUC (Plastic/Polymer Composite) | 38 pli |
| Steel | 45 pli |
🔹 Higher values indicate stronger adhesion.
CHEMICAL RESISTANCE
E6100 exhibits excellent resistance to water, dilute acids, and dilute bases.
✅ Chemicals with little or no effect on E6100:
- Distilled water
- Sulfuric acid (3% and 10%)
- Nitric acid (10% and 20%)
- Phosphoric acid (30% and 60%)
- Motor oil (30W)
- Milk, beer, wine
- Antifreeze
- Ammonium hydroxide solution (3.4%)
- Sodium borate, sodium carbonate
❌ Solvents that dissolve E6100 (avoid prolonged exposure):
- Gasoline
- Toluene
- Cyclohexane
- Perchloroethylene
- Propyl acetate
APPLICATION INSTRUCTIONS
1️⃣ Read the instructions and test on a small area. The surface must be clean, dry, and free of dirt. For best results, lightly roughen the surface before application.
2️⃣ Preparation: Trim the nozzle and puncture the inner seal. Ideal application temperature: 50°F – 90°F (10°C – 32°C).
3️⃣ Application: Apply directly to surfaces to be bonded or repaired.
4️⃣ Curing: Allow 24 hours for curing. Maximum bond strength may take 48 to 72 hours.
5️⃣ Storage: After opening, cover or plug the nozzle opening.
6️⃣ Cleaning: Remove uncured adhesive with acetone or citrus-based solvents. Once cured, remove by cutting or scraping.
HEALTH & SAFETY
This product contains perchloroethylene and drometrizole. Consult the SDS before use.
📌 Safety Data Sheet (SDS) available here:
eclecticproducts.com/downloads/sds-e6100-clear-english.pdf
